BRP Evinrude E-TEC Series Скачать руководство пользователя страница 65

Страница: 65 / 342

ENGINE MANAGEMENT MODULE (EMM)

DIAGNOSTIC SOFTWARE FUNCTIONS

Ignition Timing

Use the

Ignition Timing

screen to check and

adjust

EMM

timing.

EMM

timing must be synchro-

nized to crankshaft position.

Refer to

TIMING ADJUSTMENTS

on p. 106.

Check timing after any of the following proce-
dures:

•

Powerhead replacement

•

Crankshaft replacement

•

Flywheel removal or replacement

•

CPS replacement

•

EMM

replacement

•

EMM

software replacement

IMPORTANT:

Make sure the outboard reaches

operating temperature before making adjust-
ments.

TPS Calibration

TPS Calibration synchronizes throttle plate open-
ing with throttle position sensor voltage.

Refer to

TPS Calibration

on p. 106.

Perform TPS Calibration after replacing or adjust-
ing any throttle body or throttle linkage parts.

008143

TPS Calibration button

008144

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 65 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: