manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 175 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 175

173

POWERHEAD

POWERHEAD DISASSEMBLY

10

Throttle Linkage Removal

Remove throttle cam and throttle lever.

Shift Linkage Removal

Remove nut from shift lever. Remove shift lever
and shaft assembly.

Remove the ball, guide, and spring of the shift
detent assembly from the crankcase.

Cylinder Head Removal

Loosen 

in stages

 and remove cylinder head

retaining screws. Remove the cylinder head. Dis-
card cylinder head gasket.

Crankcase Disassembly

Remove screws and exhaust side water covers.

IMPORTANT:

Use care to avoid bending or

damaging inner exhaust side cover.

1.

Throttle cam

2.

Throttle lever

007785

1.

Nut

007745

1.

Shift detent assembly

007786

2

1

1

1

1.

Cylinder head screws (10 total)

007746

007747

007787
007788

1

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов