manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 116 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 116

114

ELECTRICAL AND IGNITION

CONNECTOR SERVICING

Packard

 

Connectors

IMPORTANT:

Always use the appropriate meter

test probes and adapters when testing compo-
nents fitted with these terminals.

Disconnect

Lift latch(s). Remove connector.

Connect

Confirm the seal is in place. Push connector onto
housing until latched.

Terminal Removal

A tab on the back side of the terminal engages a
shoulder in the connector housing to hold the ter-
minal in place. The terminal is removed by releas-
ing the tab and then pushing the terminal and wire
through connector housing.

Insert a thin tool into the connector above the ter-
minal to release tab.

Terminal Installation

Install wire gasket on wires and feed wires
through the correct terminal position of the con-
nector housing. Terminal is crimped onto wire and
then pulled back into connector housing until lock-
ing tab engages and terminal is seated.

Crimping Terminals

Strip insulation back 3/16 in. (5 mm). Position end
of wire strands in terminal past the wire crimp area
and the end of insulation in the insulation crimp
area of the terminal.

Capture all wire strands in crimp; leave no loose
strands. Crimp wire and insulation securely using
crimping pliers.

007364

1.

Tab

DRC5940a

002304

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов