BRP Evinrude E-TEC Series Скачать руководство пользователя страница 189

Страница: 189 / 342

187

POWERHEAD

POWERHEAD ASSEMBLY

Throttle Linkage Installation

Apply

Nut Lock

to threads of throttle lever screw.

Insert spring into cavity of throttle return lever.

Install lever, screw, and washer on crankcase and
hook spring on rib as shown. Tighten screw to a
torque of 120 to 144 in. lbs. (13.5 to 16 N·m).

Apply

Nut Lock

to threads of throttle cam screw.

Install cam, screw, and washer on cylinder block
and tighten screw to a torque of 120 to 144 in. lbs.
(13.5 to 16 N·m).

IMPORTANT:

Do not lubricate throttle levers or

shoulder screws.

Final Powerhead Assembly

Install the reed plate and throttle body assemblies.
Refer to

Intake Manifold Service

on p. 138.

Install oil recirculating hoses and check valves.
Refer to

OIL RECIRCULATION DIAGRAM

p. 144, or

POWERHEAD VIEWS

on p. 191.

Install thermostat and pressure valve assembly.
Refer to

THERMOSTAT AND PRESSURE

RELIEF VALVE SERVICING

on p. 164.

Install electrical harness.

Install fuel injectors and ignition coils. Refer to
Fuel Injector

Vapor Separator and Fuel Injector

Service

on p. 132.

IMPORTANT:

All injectors must be installed in

their original location. Improper injector installation
can result in powerhead failure.

Install stator and flywheel. Refer to

FLYWHEEL

AND STATOR SERVICING

on p. 103.

Install fuel pump assemblies, fuel manifolds, and
filter. Refer to

FUEL COMPONENT SERVICING

on p. 130.

Install the oil tank and oil injection hoses. Refer to

Oil Tank Assembly

on p. 155.

Install the electric starter. Refer to

Starter Instal-

lation

on p. 111.

Install

EMM

. Refer to

EMM SERVICING

on p. 66.

Install spark plugs. Refer to Spark Plug

Indexing

on p. 36.

Hook spring here

007802

Throttle cam screw

007785

WARNING

To prevent fire and explosion hazard,
make sure all electrical and ignition wiring
is routed and clamped in original posi-
tions.

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 189 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: