manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 158 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 158

156

OILING SYSTEM

OIL COMPONENT SERVICING

Installation

Align grommets with pins on powerhead. Install oil
tank assembly on powerhead. Clean mounting
screw and apply 

Nut Lock 

to threads. Install

screws and tighten to a torque of 30 to 42 in. lbs.
(3.5 to 5 N·m).

Install protective sleeves and route oil distribution
hoses from the oil distribution manifold to the
crankcase and cylinder block oil delivery fittings.
Refer to 

OIL SUPPLY DIAGRAMS

 on p. 143.

Secure oil hoses to crankcase and cylinder block
fittings with tie straps. On rope start models, install
J-clamp to retain two crankcase oil supply hoses.

Run outboard and check for leaks. Use 

Evinrude

Diagnostics

 software to activate “Oil Prime.”

Check oil flow through oil distribution hoses.
Check oil system operation and routing of oil sys-
tem hoses.

Repair any oil leaks and kinked or misrouted
hoses. Install engine covers.

Oil Injection Pump

Removal

Remove oil distribution hoses from oil manifold.
Refer to 

Oil Distribution Hoses

 on p. 154.

Remove oil from oil tank.

Remove oil tank. Refer to 

Oil Tank Assembly

 on

p. 155. Remove retaining screw from oil pump
assembly. Twist and pull up on oil pump to remove
from tank.

Installation

Apply a drop of outboard lubricant to a new oil
pump o-ring. Install o-ring on oil pump flange.

Installation is the reverse of removal.

Install oil pump retainer screw. Tighten securely. 

IMPORTANT:

Turn self-tapping screws counter

clock-wise to start the threads and clockwise to
tighten. Failure to follow this procedure can dam-
age the threads of the oil tank.

1.

Grommets

2.

Pins

007107

1.

Tie strap

2.

Clamp

007337

2

1

1

2

1.

Screw

007338

1.

O-ring

007339

1

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов