manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 133 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 133

131

FUEL SYSTEM

FUEL COMPONENT SERVICING

7

Wrap a shop towel completely around the pres-
sure test valve while connecting fitting from Fuel
Pressure Gauge, P/N 5007100, to test fitting of
fuel pump/vapor separator assembly.

Insert venting hose of gauge into a suitable con-
tainer.

Slowly open gauge’s venting valve.

Clean up any spilled fuel with shop towels.

Fuel Filter Service

Removal

Disconnect the battery cables at the battery.

Remove filter carefully to prevent spilling contents.

Inspect contents for any presence of water. If
water is present, identify the source and correct
the problem. Take additional fuel samples and
drain fuel tank(s) if necessary.

Installation

Install filter in fuel supply hoses. Flanged part of
filter is up. Secure filter with appropriate clamps.

Squeeze primer bulb to prime fuel system. Hold
pressure on bulb and check for fuel leaks.

Connect battery cables.

Run outboard and check for fuel leaks.

1.

Test fitting

007096

1.

Test fitting

2.

Venting valve

3.

Venting hose

007097

1

2

3

1

1.

Fuel filter flange

007273

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов