manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 182 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 182

180

POWERHEAD

POWERHEAD ASSEMBLY

If the installer sticks on the sleeve after installa-
tion, thread Slide Hammer, P/N 391008, into
installer and pull it off.

IMPORTANT:

Inspect sleeve after installation.

Sleeve must not be used if surface is damaged.

Use retaining ring pliers to install bearing retaining
ring with sharp edge facing away from bearing.

Lubricate a new driveshaft O-ring and lightly lubri-
cate crankshaft splines with 

Moly Lube

. Install

O-ring in sleeve.

Lightly coat the outside edge of a new lower hous-
ing seal with 

Gasket Sealing Compound

. Press

against outer case of the seal to install seal in the
lower housing with extended lip facing down.
Lubricate seal lip with 

Moly Lube

.

Install a new O-ring on the lower housing. Before
installing crankshaft into cylinder block, apply a
thin coat of 

Gasket Sealing Compound

 to outer

edge of O-ring.

Place lower seal housing on crankshaft.

Lubricate upper main bearing with outboard lubri-
cant and install on crankshaft.

Pack lip of upper oil seal with 

Moly Lube

. Place

seal on crankshaft with lip toward driveshaft and

1.

Bearing retaining ring

2.

O-ring

007797

1.

Seal lip

007798

1

2

1

1.

Lower seal housing

2.

O-ring

007799

1.

Upper main bearing

007760

2

1

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов