manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 162 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 162

160

COOLING SYSTEM

COMPONENTS

Pressure Relief Valve

A pressure relief valve is used to control water
flow and operating temperature at higher speeds
(above approximately 2800 RPM). The pressure
relief valve opens as water pressure increases.
Spring tension sets the opening pressure.

Overheating:

 A restricted or faulty valve typically

results in HIGH SPEED overheating.

Overcooling:

 Debris may prevent the valve from

closing completely.

Thermostat

The thermostat controls water flow and operating
temperature at lower speeds (below 1800 RPM).

Overheating:

 A restricted or faulty thermostat typ-

ically results in LOW SPEED overheating.

Overcooling:

 Debris may prevent the thermostat

from closing completely.

Pressure relief valve components

007369

1.

Spring, thermostat and gasket

2.

Cylinder head

007370

1

2

 

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов