manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 184 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 184

182

POWERHEAD

POWERHEAD ASSEMBLY

and tool. To seat retaining ring, swiftly strike the
driver.

Gap of retaining ring faces up, away from notch in
piston.

Installing Pistons

When all pistons and connecting rods are assem-
bled, install piston ring sets. Be sure rings are
installed in the cylinder used to test ring end gap.
Refer to 

POWERHEAD INSPECTION

 on p. 178.

IMPORTANT:

Be sure gap of ring fits squarely

around dowel pin.

IMPORTANT:

Before continuing, make sure that

all 

Gel-Seal II

 has been removed from the cylinder

block and crankcase mating flanges. If traces of
hardened 

Gel-Seal II 

are left, main bearings could

be misaligned. Refer to 

CYLINDER BLOCK

CLEANING

 on p. 177

.

Crankshaft Assembly Installation

Rotate cylinder block so crankcase mating flange
is facing up.

Apply 

Gasket Sealing Compound

 to lower oil seal

groove in cylinder block. DO NOT put any sealer
in upper seal groove.

Coat pistons, rings and cylinder walls with out-
board lubricant.

Locate piston rings on dowel pins. 

Carefully lower crankshaft assembly into the cylin-
der block. 

007764

1.

Gap of retaining ring

2.

Notch in piston

002050

2

1

002048

007750

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов