manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 242 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 242

240

MIDSECTION

TILLER HANDLE SERVICE

Connect tiller electrical connector. Secure to
retainer on starter housing.

Place battery cables and trim wiring through hole
in port lower motor cover.

Route trim wiring as shown. 

Connect electrical connector and use tie strap to
secure as shown.

Install lower motor covers. Refer to 

Lower Cover

Installation

 on p. 45.

Control Cable Installation

Make sure throttle and shift cable ends are fully
seated.

IMPORTANT:

Do NOT use threaded cable ends

to make cable adjustments.

Shift Cable Adjustment

Secure shift cable to the shift lever pin. 

For proper installation, review the following steps:

•

Place washer on pin.

•

Position retainer clip with straight section on the
bottom and angled section on the top.

•

Use long nose pliers to insert straight section of
clip into linkage pin hole.

•

Push the clip towards the hole while lifting on
the curved end with the pliers.

•

Be sure retainer clip fully engages the pin.

1.

Wire routing

2.

Retainer

007474

1.

Wire routing

2.

Secure with straps

007485

2

1

2

1

3.

Throttle cable end

4.

Shift cable end

007473

1.

Straight section

2.

Angled section

007472
007464

1

2

1
2

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов