manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 104 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 104

102

ELECTRICAL AND IGNITION

SystemCheck CIRCUIT TESTS

the two connectors, replace 

SystemCheck

gauge.

Turn the key switch OFF and reconnect all discon-
nected circuits.

LOW OIL Circuit Test

Turn the key switch ON. Using a jumper wire, con-
nect tan/black wire (pin 4) of the engine harness
connector to a clean engine ground. The LOW
OIL light should turn on after 40 seconds.

If the LOW OIL light does not turn on after con-
necting the terminal to ground, test circuit for con-
tinuity. 

Turn the key switch OFF and reconnect all discon-
nected circuits.

1.

Purple wire

2.

Tan/blue wire

DRC6280

2

 

1

002079

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов