manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 70 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 70

68

SYSTEM ANALYSIS

DIAGNOSTIC PROCEDURES

DIAGNOSTIC 
PROCEDURES

Visual Inspections

Inspect wiring and electrical connections. Disas-
semble and clean all corroded connections.
Replace damaged wiring, connectors, or termi-
nals. Repair any shorted electrical circuits.

•

Refer to 

ELECTRICAL HARNESS CONNEC-

TIONS

 on p. 85.

•

Refer to 

WIRING DIAGRAM

 at the back of this

manual.

•

Refer to 

CONNECTOR SERVICING

 on p. 111.

Make sure all ground connections are clean and
tight. Refer to 

GROUND CIRCUITS

 on p. 86.

Inspect spark plugs for wear, oil fowling, or dam-
age. A rich or lean running condition or evidence
of internal engine damage could be identified by
the appearance of the spark plugs. 

Check the fuse and the emergency stop switch
lanyard.

Operational Inspections

Run the outboard to confirm actual symptoms
before performing any unnecessary procedures.
Inspection should include the following:

•

Make sure the outboard can be cranked easily,
with no mechanical binding.

•

Check the 

EMM

 LED Indicators for system sta-

tus information. Refer to 

EMM LED INDICA-

TORS

 on p. 71.

•

Check the 

Evinrude

 

Diagnostics

 software 

Hard

Faults

 and 

Stored Faults 

screens for current

service codes. Correct any problems and clear
the codes before further troubleshooting. Refer
to 

Stored Service Codes (Faults)

 on p. 60.

Check the diagnostics software 

Profiles

, 

History

,

and 

Persistent Faults

 screens for evidence of

abnormal operation.

1.

Main engine harness ground

007343

1

Stored Faults Review Screen

008139

Profiles Screen

008146

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов