BRP Evinrude E-TEC Series Скачать руководство пользователя страница 190

Страница: 190 / 342

188

POWERHEAD

POWERHEAD INSTALLATION

POWERHEAD
INSTALLATION

Powerhead Mounting

Coat the driveshaft splines with

Moly Lube

. Do not

apply lubricant to end of driveshaft.plines.

Be sure water tube is placed in upper and lower
grommets.

Slowly lower powerhead onto exhaust housing. If
necessary, rotate flywheel in a clockwise direction
to align crankshaft and driveshaft splines.

Apply

Triple-Guard

grease to the threads of the

powerhead screws.

Loosely install all powerhead screws before tight-
ening:

Tighten the eight powerhead screws to a torque of
18 to 20 ft. lbs. (24 to 27 N·m) in the sequence
shown.

IMPORTANT:

Retighten powerhead mounting

screws after outboard has been run at full operat-
ing temperature and allowed to cool.

Water tube

Grommet

007803

007804

Powerhead screws

007741

Large screw torque sequence, 1 – 12

007774

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 190 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: