manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 16 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 16

14

ROUTINE SERVICE

INSPECTION AND MAINTENANCE SCHEDULE

INSPECTION AND MAINTENANCE SCHEDULE

Routine inspection and maintenance is necessary to prolong outboard life. The following chart provides
guidelines for inspection and maintenance to be performed by an authorized Dealer.

IMPORTANT:

Outboards used in rental, commercial, or other high hour applications require more fre-

quent inspections and maintenance. Adjust schedule for operating and environmental conditions.

Description

Engine 

Care 

Product

Routine 

Inspection

Every 300 hours 

or every three 

years 

(1)

(1) Average recreational use. Commercial use, heavy use, or use in salt or polluted water requires more frequent inspection and maintenance.

Emergency stop circuit and lanyard, check operation

Controls, steering and tilting; check operation

Engine mounting hardware, re-tighten

Fasteners, tighten any loosened components

Water intake screens, check condition

Cooling system; check water pump indicator

Anticorrosion anodes, check condition

Gearcase, check condition

Propeller, check condition

Fuel and oil systems, inspect and repair leaks 

(2)

(2) Emission-related component

Check battery connections and condition

Access 

EMM

 information, resolve any service codes

Electrical and ignition wires, inspect for wear or chafing

Fuel filter, replace

Gearcase lubricant, replace

A

Spark plugs, inspect or replace 

(2)

Thermostats, inspect and check operation 

(2)

Grease fittings, lubricate 

(3)

(3) Annually in salt water applications

C

Power trim/tilt and fluid level, inspect

B

Propeller shaft splines, inspect and lubricate 

(3)

C

Starter pinion shaft, inspect and lubricate 

(3)

D

Control cables, inspect and adjust

Steering cable, inspect and lubricate

C

Water pump, inspect / replace 

(more often if water pressure loss or overheating occurs)

A

HPF Pro

 Gearcase Lubricant

B

Biodegradeable TNT Fluid (Single ram hydraulic systems)

C

Triple-Guard

 Grease

D

Starter Bendix Lube Only

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов