manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 289 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 289

287

MANUAL STARTER

RECOIL STARTER ASSEMBLY

14

pulley. Secure retainer with left-hand threaded
nut.

Install handle on pulley pin. Pull lightly on spring
and turn pulley counterclockwise with handle until
hook end of spring engages the pulley.

Turn pulley counterclockwise until spring is com-
pletely pulled into housing.

Allow pulley to slowly unwind until tension is
relieved.

Turn pulley counterclockwise 3.5 turns, until the
pulley rope channel aligns with the rope guide.

Secure pulley by placing stop tool through the
holes in the pulley and housing.

If replacing rope, pull new rope through handle.
Tie a knot as shown.

1.

Retainer tapered end

007719

1.

Pull on spring

007720

1

1

1.

Rope channel

2.

Rope guide

007734

1.

Stop tool

007721

Handle Knot Detail

007722

1

2

1

0.375 in.

9.5 mm

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов