manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 192 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 192

190

POWERHEAD

POWERHEAD INSTALLATION

STEP 3:

 Secure shift lever to shift lever detent.

•

Remove one shift lever screw. Clean screw and
apply 

Nut Lock

 to threads.

•

Reinstall the shift lever screw.

•

Hold shift lever on midpoint line and tighten
screw to a torque of 80 to 106 in. lbs. (9 to 12
N·m).

•

Remove remaining shift lever screw. Clean
screw and apply 

Nut Lock

 to threads. Reinstall

and tighten screw to a torque of 80 to 106 in.
lbs. (9 to 12 N·m).

Adjust neutral switch. Refer to 

Neutral Switch

Adjustment

 on p. 25.

Final Adjustments

After installing a new or rebuilt

powerhead, perform the following procedures
before returning outboard to service:

•

Index all spark plugs. Refer to Spark Plug

Indexing

 on p. 36.

•

Use 

Evinrude Diagnostics

 software to start pow-

erhead break-in oiling. Refer to 

Powerhead

Break-In

 on p. 62.

•

Use 

Evinrude Diagnostics

 software to make

sure engine management software version and
revision are current. Update as required.

•

Use 

Evinrude Diagnostics

 software to confirm

neutral switch operation. Refer to 

Neutral

Switch Adjustment

 on p. 25.

•

Prime fuel system.

•

Prime oiling system. Refer to 

Oil Supply Prim-

ing

 on p. 150.

•

Use 

Evinrude Diagnostics

  software  to  check

engine timing. Refer to 

TIMING ADJUST-

MENTS

 on p. 106.

•

Run outboard and check for water, fuel, or oil
leaks.

•

Make sure engine reaches correct operating
temperature and does not overheat.

1.

Shift lever

2.

Shift lever screws

008463

1

2

NOTICE

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов