BRP Evinrude E-TEC Series Скачать руководство пользователя страница 266

Страница: 266 / 342

264

GEARCASE

GEARCASE ASSEMBLY

Holding the shifter yoke a with long-nose pliers,
install the yoke at a tilted position, locating top of
yoke into upper gearcase cavity.

Engage the shifter yoke hook onto the shifting
lever clevis pin in bottom of the gearcase cavity.

Apply

Triple-Guard

grease to threads of lower shift

rod and install into gearcase through the water
intake opening and engage the shifter yoke.

Thread the shift rod into the shifter yoke until the
rod bottoms in the yoke.

Propeller Shaft Bearing
Housing Installation

Slide the retainer plate down the propeller shaft
and into the gearcase with tab facing down.

Using Retaining Ring Pliers, P/N 331045, install
the retaining ring into groove in gearcase with
sharp outside edge facing aft.

Shifter yoke

Top of yoke

COA3229

Shifter yoke hook

COA3230

Lower shift rod

007672

Tab, retainer plate

COA3238

WARNING

Wear safety glasses and proceed with
care to avoid unsnapping the ring from the
pliers.

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 266 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: