manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 161 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 161

159

COOLING SYSTEM

COMPONENTS

9

COMPONENTS

Water Pump and Intakes

External water intakes mounted in the gearcase
housing collect water and must supply the inlet
side of the water pump with an unrestricted and
unaerated water supply. Water is drawn into the
water pump through a hole in the lower plate of
the water pump assembly. All cooling water to the
powerhead is provided by the water pump.

•

A nylon wedge (impeller key) is used to engage
the impeller bushing and driveshaft.

•

The nylon impeller housing with liner must seal
against a separate water pump plate.

•

The bottom plate MUST seal to gearcase.

Refer to 

WATER PUMP SERVICE

 on p. 250

 

for

servicing.

IMPORTANT:

The water pump housing includes

a small vent hole to the side of the water outlet. Be
sure to use the correct parts when replacing the
water pump.

Exhaust Housing

The water pump outlet connects with a water tube
and passages located in the outboard’s midsec-
tion. Grommets seal the water pump housing to
the water tube and the water tube to the exhaust
housing.

Water supplied to the exhaust housing provides all
cooling water to the cylinder block.

1.

Water inlet

2.

Water outlet

3.

Seal

4.

Plate

007366
007367

3

2

4

1

1.

Hole

007368

1

 

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов