manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 296 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 296

S–6

SAFETY

Outboard Steering Control System and Safety

What is most important?

The steering system:

•

Must not come apart;

•

Must not jam; and

•

Must not be sloppy or loose.

The outboard steering system starts 
here at the steering wheel...

...and ends here at the 
trim tab on the outboard.

What could happen?

•

If steering system comes apart, boat might turn suddenly and circle. Persons thrown into the water
could be hit.

•

If steering jams, operator may not be able to
avoid obstacles. Operator could panic.

•

If steering is loose, boat may weave while operator
tries to steer a straight course. With some rigs (at
high speed), loose steering could lead to loss of
boat control.

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов