manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 34 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 34

32

ROUTINE SERVICE

LUBRICATION

LUBRICATION

Steering System

Grease the stainless steel output end of the steer-
ing cable with 

Triple-Guard 

grease.

Use an appropriate cleaning solvent to remove
corrosion and dirt from output end of cable before
coating it with grease. Make sure wiper nut is
installed and not damaged.

Tiller Handle

Lubricate the tiller handle grease fittings with 

Tri-

ple-Guard 

grease.

Swivel Bracket and Trailering 
Bracket

Lubricate the swivel bracket with

 Triple-Guard

grease.

Apply grease until the grease begins to flow from
the upper or lower swivel bracket areas.

Coat the pivot points of the trailering bracket with

Triple-Guard

 grease.

Tilt Tube

Lubricate the tilt tube grease fittings with 

Triple-

Guard 

grease.

WARNING

Failure to regrease as recommended
could result in steering system corrosion.
Corrosion can affect steering effort, mak-
ing operator control difficult.

1.

Steering cable

2.

Wiper nut

DR29546

1.

Tiller handle fittings

007020A

1

2

1

1

1.

Grease fitting

2.

Tilt support

007032

1.

Tilt tube fittings

2.

Swivel bracket fittings

007033

2

1

1

2

1

2

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов