manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 106 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 106

104

ELECTRICAL AND IGNITION

FLYWHEEL AND STATOR SERVICING

Use Flywheel Holder, P/N 771311, or equivalent,
and a 28 mm socket to remove flywheel nut. 

Apply 

Moly Lube 

grease to the threads of the

puller pressing screw, P/N 307637, and the center
hole of the crankshaft.

Assemble the following components from Univer-
sal Puller Set, P/N 378103:

•

Body, P/N 307636

•

Screw, P/N 307637

•

Handle, P/N 307638

•

Three screws P/N 309492

•

Three washers, P/N 307640

Put the puller on flywheel with body flat side up.
Attach the puller body with the three shoulder
screws and washers. Hold puller body with han-
dle, and tighten pressing screw until flywheel
releases. Turn the center screw and lift the fly-
wheel off of the crankshaft.

Stator Service

Disconnect stator harness connector.

Remove three allen head screws to remove stator.

To install stator, position stator on cylinder block.
Apply 

Nut Lock

 to screw threads. Install screws

and tighten in crossing pattern to a torque of 84 to
106 in. lbs. (9.5 to 12 N·m).

Flywheel Installation

Install the outer edge of flywheel key parallel with
centerline of crankshaft.

007359

1.

Universal puller

007360

1

1.

Stator screws

007443

CAUTION

To avoid injury, keep hands and fingers
clear from underside of flywheel. Flywheel
can snap toward stator with great magnetic
force.

1.

Flywheel key

DRC2116

1

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов