manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 18 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 18

16

ROUTINE SERVICE

LIFTING THE OUTBOARD

Lower outboard onto the pad. Use hoist to care-
fully roll the outboard onto its port side.

Remove chain from lifting tool. 

Remove lifting tool from outboard. 

Attach chain to lift eye on back of engine block.

Carefully lift engine with hoist.

To avoid damage to the outboard,

lift the outboard in one smooth motion. DO
NOT allow the outboard to bounce.

CAUTION

To avoid damage to the outboard, DO NOT
allow the outboard to fall unrestrained.

007211

WARNING

If the chain snap hooks are too large, the
cast in lift eye could break causing the out-
board to drop suddenly causing personal
injury and damaging the outboard.

1.

Lift eye

007212

007213

1

NOTICE

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов