manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 22 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 22

20

ROUTINE SERVICE

OUTBOARD RIGGING CONNECTIONS

SystemCheck Harness 
Connections

Before installing electrical connectors, check that
the seal is in place. Clean off any dirt from con-
nectors. Apply a light coat of 

Electrical Grease

 to

the seal only. DO NOT fill connectors with 

Electri-

cal Grease

.

Route electrical harness along the edge of the
lower engine cover.

Secure connectors to lower motor cover with two
tie straps as shown.

Route trim and tilt connector under air silencer.
Use tie strap to secure connector as shown.

Install battery cables and secure with tie strap.

Route battery cable through grommet of port
lower motor cover.

BE SURE all harnesses and wires

are not pinched, cannot contact flywheel, and
do not interfere with moving throttle or shift
linkages.

1.

Seal

42079A

1.

Key switch connector

2.

Tachometer connector

007263

1.

Wire routing

2.

Secure with two tie straps

007125

1

2

1

1

2

1.

Trim and tilt connector

007264

1.

Tie strap

2.

Battery cable ground

007240

1.

Battery cable grommet

008009

1

2

1

1

NOTICE

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов