BRP Evinrude E-TEC Series Скачать руководство пользователя страница 243

Страница: 243 / 342

241

MIDSECTION

TILLER HANDLE SERVICE

•

Lock the retainer by moving the angled section

behind

the straight section.

Pull firmly on shift cable casing to remove back-
lash.

With outboard and shift lever in NEUTRAL, place
shift cable on the trunnion bracket of intake mani-
fold as shown. Rotate the anchor to align.

Install washer between anchor and trunnion
bracket. Install screw. Tighten screw to a torque of
84 to 106 in. lbs. (9.5 to 12 N·m).

Throttle Cable Adjustment

Install throttle cable connector with Ball Socket
Installer tool, P/N 342225.

Place throttle cable through upper trunnion
pocket.

Hold twist grip in IDLE position. Pull firmly on
cable to remove backlash.

Locked Retainer Clip
1.

Angled section behind straight section

007465

Anchor

007466

Screw

007467

Installer tool, P/N 342225

007468

007469

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 243 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: