manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 263 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 263

261

GEARCASE

GEARCASE ASSEMBLY

12

Driveshaft Seals

Apply 

Gasket Sealing Compound

 to the metal

casing of the seals before installing.

Use Seal Installer, P/N 326552, to install the inner
seal with flush lip facing into the gearcase, then
the outer seal with extended lip facing out of the
gearcase.

Apply 

Triple-Guard

 grease to the seal lips after

installing.

GEARCASE ASSEMBLY

Propeller Shaft, Gear and Shifter
Installation

IMPORTANT:

Make no dry assemblies. Lubri-

cate all bearings, shafts, and gears with gearcase
lubricant.

Oil and place the forward bearing cone and roller
assembly in the forward bearing cup.

Install the small thrust washer with the chamfered
inside diameter facing the pinion gear. Oil and
install the thrust bearing. Install the large thrust
washer with chamfered outside edge facing up.

1.

Seal Installer, P/N 326552

2.

Inner seal

3.

Outer seal

DR2061
DR2062

1

2

3

38635

1.

Small thrust washer, chamfered inside diameter

2.

Thrust bearing

3.

Large thrust washer, chamfered outside edge

803051

2

3

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов