manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 19 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 19

17

ROUTINE SERVICE

OUTBOARD RIGGING CONNECTIONS

2

OUTBOARD RIGGING 
CONNECTIONS

IMPORTANT:

For complete outboard rigging

and remote control installation information, refer to
the 

Predelivery and Installation Guide

 included

with the service manual set.

Common Practices – All Models

Control Cable Identification

IMPORTANT:

Control cable function must be

identified before rigging outboard.

Identify each control cable:

•

Put the control handle into NEUTRAL position.
The throttle cable casing guide will retract com-
pletely and the shift cable casing guide will go to
the midpoint of its travel.

Extend the control cables and lubricate them with

Triple-Guard

 grease.

Cable Retainer Clip Installation

When installing retainer clips on control arm link-
age pins, clips should be locked and 

must not

 be

bent or deformed.

For proper installation, review the following steps:

•

Place washer on pin.

•

Position retainer clip with straight section on the
bottom and angled section on the top.

•

Use long nose pliers to insert straight section of
clip into linkage pin hole.

•

Push the clip towards the hole while lifting on
the curved end with the pliers.

•

Be sure retainer clip fully engages the pin.

•

Lock the retainer by moving the angled section

behind

 the straight section.

1.

Shift cable casing guide extended to midpoint

2.

Throttle cable casing guide retracted

DP0811

30501

1

2

1.

Straight section

2.

Angled section

DP0818

DSC_4670

Locked Retainer Clip
1.

Angled section behind straight section

DP0817a

1

2

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов