manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 56 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 56

54

ENGINE MANAGEMENT MODULE (EMM)

EXTERNAL SENSORS

Engine Temperature Sensor

Monitors cylinder head temperature.

If cylinder head temperature exceeds 212° F
(100° C) below 3500 RPM, the 

EMM

:

If cylinder head temperature exceeds 194° F
(90° C) above 3500 RPM, the 

EMM

:

If cylinder head temperature exceeds 248°F
(120°C), the 

EMM:

The outboard will not restart after a temperature
related SHUTDOWN until the engine temperature
returns to normal. Refer to 

SHUTDOWN MODE

on p. 58.

If sensor values are less than -15°F (-26.1°C) or
greater than 332°F (166.5°C), the 

EMM:

If sensor values are below -4°F (-20°C), the 

EMM:

If cylinder head does not reach operating temper-
ature (104°F / 40°C below 2300 RPM) in 10 min-
utes, the 

EMM

: 

Low Oil Switch

The low oil switch monitors the oil level in the oil
tank.

If the oil level falls below one-quarter capacity, the

EMM

 begins counting oil pump pulse cycles.

When it reaches 1000 pulses, the 

EMM

 signals:

After LOW OIL is displayed, the 

EMM

 counts oil

pump pulse cycles again. When it reaches 6700
pulses, the 

EMM

:

To recover from 

S.A.F.E.

 mode:

•

Oil level must be above one-quarter

•

The warning resets after three oil pump pulse
cycles when the outboard has been stopped
and restarted.

If outboard has been run for more than 3 hours
with NO OIL faults (codes 34 & 117), the 

EMM

If the 

EMM

 detects the low oil sensor circuit is

open, the 

EMM

:

Activates 

S.A.F.E.

Stores service code 40

EMM

 LED 4: ON (Running)

Activates 

S.A.F.E.

Stores service code 43

EMM

 LED 4: ON (Running)

Activates SHUTDOWN
Stores service code 31

EMM

 LED 4: FLASHING

Stores service code 41

EMM

 LED 3: OFF (Cranking)

EMM

 LED 3: ON (Running)

Stores service code 42

EMM

 LED 3: OFF (Cranking)

EMM

 LED 3: ON (Running)

Stores service code 58

EMM

 LED 3: OFF (Cranking)

EMM

 LED 3: ON (Running)

Engine Monitor LOW OIL display: ON

Activates 

S.A.F.E.

Stores service code 117

EMM

 LED 4: ON (Running)

Engine Monitor LOW OIL display: ON

Activates SHUTDOWN
Stores service code 33

EMM

 LED 4: FLASHING

Engine Monitor LOW OIL display: FLASHING

Activates 

S.A.F.E.

Stores service code 120

EMM

 LED 4: ON (Running)

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов