manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 234 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 234

232

MIDSECTION

TILLER HANDLE SERVICE

If replacing tilt detent pawl, tilt release lever, tilt
detent pin or spring, remove cotter pin and roll
pins as needed. 

Remove four screws and bushing from bracket.
Remove bracket from handle.

Inspection

Inspect the throttle cable for kinks and wear.
Replace if necessary.

Inspect the shift cable for kinks and wear. Replace
if necessary.

Inspect the steering handle components for wear,
cracks, or damage. Replace parts if necessary.

Refer to 

Emergency Stop Switch Test

 on p. 99

to test stop switch.

Assembly

Install bracket on handle. Install four screws.
Tighten screws securely and install bushing in
bracket. 

1.

Cotter pin

007550

1.

Roll pins

007551

1.

Screws

2.

Bushing

007552

1

1

2

1

CAUTION

When reinstalling screws in composite
materials turn screws COUNTER-CLOCK-
WISE until threads of screw engage
threads of screw boss. 

Failure to follow this procedure will dam-
age the screw boss threads. Once threads
are engaged, tighten screws securely.

1.

Screws

2.

Bushing

007552

2

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов