manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 40 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 40

38

ROUTINE SERVICE

ANTI-CORROSION PROTECTION

ANTI-CORROSION 
PROTECTION

Sacrificial Anodes

Galvanic

 

corrosion occurs in fresh or salt water.

Salt, brackish, and polluted water can accelerate
corrosion. “Sacrificial” anodes are intended to pro-
tect the underwater metal components of the out-
board from galvanic corrosion.

Manual tilt outboards are equipped with one sacri-
ficial anode. Power tilt outboards are equipped
with two sacrificial anodes.

Visually inspect anodes and metal components
below water level. Erosion of anodes is normal
and indicates the anodes are functioning properly.

IMPORTANT:

Anodes that are not eroding may

not be properly grounded. Anodes and the mount-
ing screws must be clean and tight for effective
corrosion protection.

For best anode performance:

•

Replace all anodes that have eroded or disinte-
grated to two-thirds of their original size

•

Do not paint or apply protective coatings to
anodes or anode fasteners

•

Avoid using metal-based antifouling paint on the
boat or outboard.

Testing Procedure – Continuity

Connect ohmmeter leads between engine ground
and anode surface.

The meter should show little or no resistance. If
resistance is high, check the following:

•

Remove the anode and clean the area where
the anode is installed

•

Clean the mounting screws

•

Install the anode and test again.

Metallic Component Protection

Protect metal components on outboards from cor-
rosion. Use the following products to minimize
corrosion:

•

Anti-Corrosion Spray 

provides a heavy, waxy

coating to protect components

•

“6 in 1” Multi-Purpose Lubricant 

provides a thin

film of anti-corrosion protection.

Exterior Finishes

Maintain the outboard’s exterior finish to prevent
corrosion and reduce oxidation:

•

Use automotive wax to protect the outboard’s
exterior finish from oxidation.

•

Clean regularly using clean water and mild
detergent soap.

•

Touch-up damage to painted surfaces promptly.

1.

Stern bracket anode (Power tilt models only)

2.

Gearcase housing anode

007436

1

2

1.

Meter lead to anode

007268

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов