manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 64 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 64

62

ENGINE MANAGEMENT MODULE (EMM)

DIAGNOSTIC SOFTWARE FUNCTIONS

Oil Control Settings

Set Oil Type

The TC-W3 oil type setting is the standard setting
for all outboards. Set TC-W3 for:

•

Operation with all TC-W3 outboard oils includ-
ing 

XD30, XD50, or XD100

•

Applications requiring maximum lubrication

•

Extreme applications (racing or harsh condi-
tions).

The 

XD100

 setting provides an option to run the

outboard at a reduced oil injection rate. This set-
ting REQUIRES the use of 

Evinrude XD100

 out-

board lubricant and is not recommended for all
applications.

Use the 

XD100

 setting for:

•

Conventional use (runabouts, cruisers)

•

Moderate applications.

Powerhead Break-In

Use the diagnostics software to start break-in oil-
ing after a powerhead rebuild. The break-in oiling
program runs for two hours of outboard operation,
above 2000 RPM.

Tiller/Remote Programming

This feature controls the start in gear protection
function of the neutral switch. Tiller operated mod-
els, including remote models with an installed tiller
conversion kit, MUST be set to TILLER.

1.

Oil control setting

008142

CAUTION

Running an Evinrude E-TEC outboard on
other grades of oil while set to the XD100
oil ratio will result in increased engine
wear and shortened outboard life.

1

1.

Break-in oil setting

008142

1.

Starter mode setting

008142

1

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов