BRP Evinrude E-TEC Series Скачать руководство пользователя страница 107

Страница: 107 / 342

105

ELECTRICAL AND IGNITION

IGNITION COIL SERVICING

Thoroughly clean the crankshaft and flywheel
tapers with

Cleaning Solvent

™

and let dry.

Align the flywheel keyway and install flywheel.

Coat the threads of the flywheel nut with

Triple-

Guard

grease.

Install the washer and nut and tighten to a torque
of 66 to 70 ft. lbs. (90 to 95 N·m).

To prevent damage to crankcase or

cylinder block, DO NOT allow Flywheel Holder
to rest against recoil starter mounting boss.

Replace recoil starter.

IMPORTANT:

Check ignition timing after fly-

wheel removal or replacement. Refer to

TIMING

ADJUSTMENTS

on p. 106.

IGNITION COIL
SERVICING

Ignition Coil Removal

Remove spark plug lead from ignition coil and dis-
connect ignition coil electrical connector.

Remove two ignition coil retaining screws.

Do not lose the rubber washers between coil and
bracket.

Ignition Coil Installation

Install one rubber washer on each screw and
install screw through ignition coil.

Install remaining rubber washers on screws
between coil and bracket.

Install coil on bracket. Tighten screws to a torque
of 31 to 49 in. lb. (3.5 to 5.5 N·m).

Install spark plug lead on ignition coil and connect
ignition coil electrical connector.

002093

007361

NOTICE

Screws

008193

Rubber washers

008188

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 107 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: