manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 236 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 236

234

MIDSECTION

TILLER HANDLE SERVICE

Use an appropriate tool to align screw hole
through the tiller handle, bracket and base. Install
steering handle screw. Tighten screw so tiller han-
dle pivots easily. Refer to 

Tiller Handle Friction

on p. 25.

Install bushing, washer and nut on port side of
tiller handle. Tighten nut to a torque of 25 to 28 ft.
lbs. (35 to 38 N·m).

Install the throttle friction control.

Press the trim switch into the twist grip. Be sure
trim switch UP position aligns with the twist grip
indicator line as shown.

Install trim switch wiring through inner steering
handle. 

IMPORTANT:

Trim switch wiring must NOT be

twisted through the throttle twist grip or inner tiller
handle / wire guide. 

Insert wire guide into inner steering handle.

1.

Steering handle screw

007548

1.

Nut

2.

Washer

3.

Bushing

007547

1.

Throttle friction control

007546

1

3

2

1

1

1.

Trim switch UP position

2.

Indicator line

007554

1.

Inner tiller handle

2.

Wire guide

3.

Trim switch wires

007555

2

1

3

2

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов