BRP Evinrude E-TEC Series Скачать руководство пользователя страница 276

Страница: 276 / 342

274

TRIM AND TILT

TRIM AND TILT REPLACEMENT

Remove the clip from the cylinder pin.

Thread Adapter, P/N 340624, onto Slide Hammer,
P/N 391008. Screw the adapter into the cylinder
pin and remove the pin.

Remove one of the locknuts from the angle adjust-
ment rod. Remove the rod from the stern brack-
ets.

Remove the unit from the stern brackets far
enough to remove the ground lead from the pump
motor mounting screw.

Installation

Lubricate the cylinder and thrust rod bushings with

Triple-Guard

grease. Install the bushings.

Install the ground lead.

Place trim/tilt unit into position.

15493

Adapter

Slide hammer

Cylinder pin

007638

007639

1
2

Ground lead

007640

Bushings

007648

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 276 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: