manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 113 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 113

111

ELECTRICAL AND IGNITION

CONNECTOR SERVICING

6

Starter Installation

Apply 

Triple-Guard

 grease to the threads of the

three starter screws and also to the washers.

Position the starter and install the screws and
washers. Tighten screws to a torque of 168 to 192
in. lbs. (19 to 21 N·m).

Attach starter positive (+) cable to post with lock
washer and nut; tighten securely.

Coat connections with 

Black Neoprene Dip

.

CONNECTOR 
SERVICING

DEUTSCH Connectors

IMPORTANT:

Electrical Grease

 is recom-

mended. Incorrect grease application can cause
electrical or warning system problems.

To disconnect the connector, press the latch and
pull the connectors apart.

To connect the connector, confirm that the seal is
in place. Clean off any old grease and dirt from
connectors. Apply a light coat of 

Electrical Grease

to seal only. Push connectors together until
latched.

Terminal Removal

Use hook-end of Connector Service Tool,
P/N 342667, to pull out wedge from receptacle, or
use other end of tool to pry out wedge from plug.
Use needle-nose pliers to remove wedge from
3-pin receptacle.

007355

1.

Latch

2.

Seal

42079A

1.

Wedge

42327

2

1

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов