manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 122 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 122

120

FUEL SYSTEM

FUEL SYSTEM REQUIREMENTS

FUEL SYSTEM 
REQUIREMENTS

Regulations and Guidelines

Vessel manufacturer, and/or installer of an EPA
certified outboard, must meet minimum specifica-
tions for boat fuel systems established by:

•

U.S. Environmental Protection Agency (EPA)
– 40 CFR 1045.112
– 40 CFR 1060

•

U.S. Coast Guard (USCG)
– 33 CFR 183

•

American Boat & Yacht Council (ABYC)
– Standard H-24
– Standard H-25.

Portable Fuel Tanks

Do not use portable fuel tanks for

outboards larger than 115 HP. Inadequate fuel
flow to high horsepower outboards can result
in serious powerhead damage.

Fuel Flow Requirements

WARNING

If engine is equipped with a quick-discon-
nect fuel hose, you MUST disconnect the
fuel hose from the engine and the fuel tank
to prevent fuel leaks:

•

Whenever the engine is NOT being used

•

Whenever the engine is being trailered

•

Whenever the engine is in storage.

NOTE: A small amount of fuel may be
released when the fuel connector is dison-
nected.

Store portable fuel tanks in well-ventilated
areas, away from heat sources and open
flames. Close the vent screw of the fuel
tank cap, if equipped, to prevent escape of
fuel or fuel vapors which could acciden-
tally ignite. Do not allow disconnected fuel
hoses to leak fuel.

NOTICE

15 – 30 HP

40 – 90 HP

115 – 300 HP

Fuel tank pickup tube

1/4 in. (6.4 mm) min. ID

5/16 in. (7.9 mm) min. ID

3/8 in. (9.5 mm) min. ID

Fuel fittings

5/32 in. (4.1 mm) min. ID

1/4 in. (6.4 mm) min. ID

9/32 in. (7.1 mm) min. ID

Fuel supply hoses

1/4 in. (6.4 mm) min. ID

3/8 in. (9.5 mm) min. ID

3/8 in. (9.5 mm) min. ID

ALL MODELS

Fuel tank pickup 
screen

100 mesh, 304 grade stainless steel wire, 0.0045 in. wire diameter, 1 in. (25 
mm) long

Antisiphon valve

2.5 in. (63.5 mm) Hg maximum pressure drop at 20 gph (76 l/hr) flow

Remote fuel filter

0.4 in. Hg maximum pressure drop at 20 gph (76 l/hr) flow, 
150 in.

2

 (1290 cm

2

) of filter area

Maximum fuel pump 
lift height

Fuel pump should not be located more than 30 in. (76.2 cm) above bottom of 
fuel tank

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов