manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 227 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 227

225

MIDSECTION

STERN BRACKET – MANUAL TILT MODELS

11

Apply a light coat of 

Triple-Guard

 grease to the

outside of the lower bushing. Install bushing in the
swivel bracket.

Use Seal Installation tool, P/N 350958, to install
new upper and lower seals in the swivel bracket.
Install seals with lips of seals facing in.

Install the steering friction plate, washers and
lever.

Apply 

Triple-Guard

 grease to both sides of thrust

washer. Install thrust washer on steering arm.

Slide the steering arm through the swivel bracket.

Align slots of friction washers with dowel pin.

1.

Lower bushing

007588

1.

Seal

007621
007622

1.

Steering friction plate

2.

Steering friction washers

3.

Steering friction lever

007686

1

1

1

2

3

1.

Thrust washer

007617

1.

Thrust washer

007623

1.

Steering friction lever

2.

Friction washers

3.

Friction plate

4.

Dowel pin

007491

1

1

3

1

4

2

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов