BRP Evinrude E-TEC Series Скачать руководство пользователя страница 218

Страница: 218 / 342

216

MIDSECTION

STERN BRACKET – MANUAL TILT MODELS

STERN BRACKET –
Manual Tilt Models

Clamp Screw Service

Inspect clamp screw assemblies. Replace swivel
plate and shoulder screw if bent or loose.

Disassemble swivel plate and shoulder screw.

Inspect and clean clamp screw and shoulder bolt
threads.

Install clamp screw and handle assembly in tran-
som bracket.

Install swivel plate, onto shoulder screw.

Apply

Locquic Primer

to the threads of the screw

and allow it to dry four to five minutes. Then apply

Ultra Lock

to threads.

Install shoulder screw and swivel plate onto clamp
screw and handle assembly.

Tighten screw to a torque of 60 to 84 in. lbs. (7.5
to 9 N·m).

Check for free movement of swivel plate on shoul-
der bolt.

Stern Bracket Disassembly
(Manual Tilt)

If outboard is equipped with a tiller arm, remove
the tiller arm. Refer to

TILLER HANDLE SER-

VICE

on p. 227.

Remove exhaust housing. Refer to

EXHAUST

HOUSING SERVICE

on p. 203.

Remove lower mount bracket retaining screws.

Clamp screw and handle assembly

007579

Swivel plate

Shoulder screw

007580

007581

Screws

007582

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 218 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: