manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 224 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 224

222

MIDSECTION

STERN BRACKET – MANUAL TILT MODELS

Place the shallow water drive link and reverse
lock assembly into the swivel bracket as shown
Install one pin as shown and secure pin with clip.

Install remaining pin through reverse lock assem-
bly and into boss. Use an appropriate tool to hold
spring in alignment. Push pin through spring and
swivel bracket. Secure pin with clip.

IMPORTANT:

Make sure the rounded end of the

spring is installed as shown. 

Use an appropriate tool to hook the straight end
over the pin as shown. 

Install the tilt lock lever and port stop link in the
swivel bracket. Install the bellcrank, temporarily
leave the bell crank screw loose.

Be sure the tilt lock lever cam and port stop link
cam are installed as shown.

1.

Pin

007606

1.

Pin

2.

Boss

3.

Spring

007607

1.

Spring rounded end

007608

1

1

2

3

1

1.

Spring straight end

007609

1.

Bellcrank

2.

Tilt lock lever

3.

Stop link

007610

1.

Port stop link cam

2.

Tilt lock lever cam

007611

007612

1

2

1

3

1

2

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов