manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 27 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 27

25

ROUTINE SERVICE

ADJUSTMENTS

2

Tiller Height Adjustment

The angle of the tiller handle can be raised or low-
ered by adjusting a thumbscrew under the handle. 

Tiller Handle Ratchet

Tiller models feature a ratchet which holds the
tiller arm at approximately 30° or 90° positions. To
release the tiller arm, press up on the release
lever.

Tiller Handle Friction

The tiller handle screw may be tightened to adjust
the amount of friction when tilting the tiller handle.

Neutral Switch Adjustment

Adjust neutral switch as follows:

Make sure neutral switch is centered on shift lever
detent.

•

Loosen two neutral switch bracket screws.

•

Center the neutral switch on lobe of the shift
lever detent.

•

Hold neutral switch bracket in position and
tighten screws to a torque of 35 to 60 in. lbs.
(4 to 6.8 N·m). 

Check Neutral Switch Operation

Use 

Evinrude Diagnostics

 software “Monitor”

screen to confirm neutral switch operation. 

1.

Height adjustment screw

007453

1.

Release lever

007483

1

1

1.

Screw

007484

1.

Neutral switch

2.

Lobe of shift lever detent

3.

Neutral switch bracket screws

008462

1

3

1

3

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов