BRP Evinrude E-TEC Series Скачать руководство пользователя страница 92

Страница: 92 / 342

ELECTRICAL AND IGNITION

STATOR TESTS

OPE

TART

ODELS

Use a Peak Reading Voltmeter, P/N 507972, to
check stator output voltage. Set meter to the
50 VAC scale.

Disconnect CPS. Remove spark plugs. Make sure
outboard is in NEUTRAL. Refer to

SPARK

PLUGS

on p. 36.

Disconnect stator (6-pin) connector from the
engine harness (6-pin)

connector.

Connect Stator Test Adaptor tool, P/N 354719, to
stator connector.

Connect meter leads to terminals of adaptor tool.

Rotate the flywheel with the starter rope, using a
long, steady pull.

Stator output voltage should be approximately
30 VAC.

IMPORTANT:

Index all spark plugs. Refer to

Spark Plug

Indexing

on p. 36.

WARNING

To prevent accidental starting of outboard,
disconnect crankshaft position sensor
(CPS).

Stator Test Adaptor

006750

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 92 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: