BRP Evinrude E-TEC Series Скачать руководство пользователя страница 295

Страница: 295 / 342

S–5

SAFETY

Outboard Speed Control System and Safety

What is most important?

The outboard speed control system
starts here at the remote control
lever... (single lever remote control)

...and ends here on
the powerhead.

When control lever is moved from
FORWARD (or REVERSE) to
NEUTRAL...

Powerhead speed must
slow down to allow operator
to shift into NEUTRAL.

Operator must be able to
STOP propeller.

What could happen?

If Operator cannot slow down the outboard or shift into NEUTRAL gear (stop propeller), Operator
could panic and lose control of boat.

How can loss of speed control be minimized?

When

rigging
or after

servicing

Read

understand

, and

follow

manufacturer’s

instructions

•

Follow warnings marked “

” closely.

•

Assemble parts carefully.

•

Make adjustments carefully.

•

Test your work. Do not guess. Make sure speed control system does just what the oper-
ator wants and nothing else.

•

Make sure full throttle can be obtained so Operator will not overload parts.

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 295 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: