manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 20 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 20

18

ROUTINE SERVICE

OUTBOARD RIGGING CONNECTIONS

Cable, Hose, and Wire Routing

Refer to 

Control Cable Identification

 on p. 17.

Remove cable entry grommet cover and grommet.

Remove rubber membrane from grommet holes
as needed.

Install cables and wiring harness(es) through
grommet as shown:

When grommet is in place and all cables have
been installed, tighten a tie strap around the out-
side of the grommet to form a watertight seal
around the cables.

Place blank sealing decal on lip of lower motor
cover at each harness connector tie strap to pre-
vent water intrusion.

After installation, make sure there

is enough clearance for all cables to avoid
binding or chafing through all engine steering
and tilting angles.

Control Cable Installation

Refer to 

Control Cable Identification

 on p. 17.

Make sure the remote control is in NEUTRAL, and
throttle is in the IDLE position.

Removal of lower motor covers is NOT required.
Some images show lower covers removed for
clear illustration.

Place the shift cable on the shift lever pin.

Hold the shift linkage in NEUTRAL.

Push and pull on the shift cable and observe the
cable slack. Hold the casing guide in the center of
the slack.

CAUTION

To prevent accidental starting while servic-
ing, disconnect the battery cables at the
battery. Twist and remove all spark plug
leads.

1.

Cable entry grommet cover

007120

1.

Throttle cable

2.

Shift cable

3.

Tiller wiring harness

007129

1

1

2

3

1.

Tie strap

1.

Blank sealing decal

007127

1

2

NOTICE

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов