BRP Evinrude E-TEC Series Скачать руководство пользователя страница 62

Страница: 62 / 342

ENGINE MANAGEMENT MODULE (EMM)

DIAGNOSTIC SOFTWARE FUNCTIONS

Dynamic Information

Dynamic information is viewed while the outboard
is running. Changes in data, such as voltages or
temperatures, are shown as they happen.

Stored Service Codes (Faults)

Service codes are stored if an abnormal condition
occurs while the outboard is running.

The

Stored Faults

screen of the diagnostics soft-

ware shows the code number, the number of
times the event occurred, and operating hours of
first and last occurrences.

Hard Faults

A hard fault is a service code that currently exists.
Hard faults become stored faults only if the out-
board is running.

Persistent Faults

The

Persistent Faults

screen keeps a history of all

previously stored codes, including code number,
the number of times the event occurred, and oper-
ating hours of the last occurrence.

Persistent faults cannot be erased.

Static Tests

Static Tests allow diagnostic testing of system
components while the outboard is NOT running.

Monitor Screen

008137

Stored Faults Review Screen

008139

Hard Faults Review Screen

008138

Static Tests Screen

008140

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 62 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: