manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 134 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 134

132

FUEL SYSTEM

FUEL COMPONENT SERVICING

Fuel Lift Pump Service

The fuel lift pump is serviceable as a complete
assembly. Refer to parts catalog for service parts.

Removal

Disconnect the battery cables at the battery.

Remove port lower motor cover. Refer to 

Lower

Cover Removal

.

Remove the oil tank. Refer to 

Oil Tank Assembly

on p. 155.

Use an appropriate tool to remove the push nuts
that retain fuel pump to oil tank.

Remove the fuel hoses from the fuel pump hous-
ing.

Remove the fuel lift pump. 

Installation

Connect the fuel hoses to the fuel pump. Secure
with 

Oetiker

 clamps. 

Place fuel pump in position on the oil tank. Secure
the fuel pump with new pushnuts, P/N 354365. 

Be sure fuel hoses are routed in channels on oil
tank. Install the oil tank. Refer to 

Oil Tank Assem-

bly

 on p. 155

.

Squeeze primer bulb to prime fuel system. Hold
pressure on bulb and check for fuel leaks.

Connect battery cables.

Run outboard and check for fuel leaks.

Vapor Separator and Fuel Injector 
Service

Vapor Separator Removal

Relieve fuel system pressure. Refer to 

Relieving

Fuel System Pressure

 on p. 130.

Disconnect the battery cables at the battery.

Remove oil tank. Refer to 

Oil Tank Assembly

 on

p. 155. 

1.

Fuel pump housing

007410

1

1.

Push nuts

007422

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов