manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 77 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 77

75

SYSTEM ANALYSIS

IGNITION OUTPUT TESTS

5

Static Ignition Test

Perform the static ignition test using 

Evinrude

Diagnostics

 software and an inductive timing light.

IMPORTANT:

Do NOT perform static tests using

Diagnostic Power Supply Tool, P/N 587005, with
internal 9 volt batteries only. This will produce
false results. Refer to 

Communication

 on p. 58.

IMPORTANT:

DO NOT use a spark checker

tool. Radio Frequency Interference (RFI) gener-
ated by the arcing current can cause erratic 

EMM

operation.

The outboard must NOT be running and the emer-
gency stop switch lanyard must be installed.

Connect timing light pickup to the secondary cir-
cuit (spark plug lead) of the cylinder being tested.
Activate test and observe timing light strobe for
consistent flash.

IMPORTANT:

This test is operating the ignition

coil with 12 V battery power on the system voltage
(55 V) circuit. An inductive probe with low sensitiv-
ity may not be able to detect the signal.

Results:

No spark on one or more cylinders:

•

Inspect or replace spark plugs

•

Refer to 

Ignition Control Circuit Tests

 on

p. 77

•

Refer to 

Ignition Coil Tests

 on p. 77

Steady spark on all cylinders:

•

Refer to 

Running Ignition Tests

 on p. 76 and

DYNAMIC TESTS

 on p. 70.

Static Tests Screen

008140

1.

Timing light pick-up

2.

Spark plug lead

007398

1

2

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов