Alcatel-Lucent 060321-10, Rev. B Скачать руководство пользователя страница 352

Страница: 352 / 2354

show multi-chassis vf-link member-port

Multi-Chassis Commands

page 7-28

OmniSwitch CLI Reference Guide

March 2011

show multi-chassis vf-link member-port

Displays detailed information about the configured and operational parameters related to the virtual fabric
link member ports on the switch.

show multi-chassis vf-link member-port [slot/port]

Syntax Definitions

slot/port

Specify the slot number for the module and the physical port number on
that module (e.g., 3/1 specifies port 1 on slot 3).

Defaults

Platforms Supported

OmniSwitch 10K

Usage Guidelines

Examples

-> show multi-chassis vf-link member-port

VFLink ID Slot/Port Oper Is Primary

----------+-----------+---------+------------

0 1/1 Up No

0 1/2 Up Yes

0 1/17 Up No

0 1/18 Up No

-> show multi-chassis vf-link member-port 3/1

VFLink ID Slot/Port Oper Is Primary

----------+-----------+---------+------------

0 1/2 Up Yes

Output fields are defined here:

output definitions

VFLink ID

Virtual Fabric Link identifier. Currently a single virtual fabric link with
identifier equalt to zero is supported.

Slot/Port

The slot/port that defines each of the physical ports that are members of
the virtual fabric link.

Содержание 060321-10, Rev. B



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 060321-10, Rev. B

Отзывы:

Похожие инструкции для 060321-10, Rev. B

Бренды по названию

Популярные бренды

Alcatel-Lucent 060321-10, Rev. B, Справочное руководство CLI

Результаты поиска

Содержание 060321-10, Rev. B

Отзывы:

Похожие инструкции для 060321-10, Rev. B

Бренды по названию

Популярные бренды