Alcatel-Lucent 060321-10, Rev. B Скачать руководство пользователя страница 738

Страница: 738 / 2354

show ip bfd sessions

BFD Commands

page 14-30

OmniSwitch CLI Reference Guide

March 2011

Release History

Release 7.1.1; command was introduced.

Related Commands

MIB Objects

alaBfdSessTable

alaBfdSessDiscriminator

alaBfdSessNeighborAddr

alaBfdSessSessionType

alaBfdSessIfIndex

alaBfdSessUdpPort

alaBfdSessState

alaBfdSessOperMode

alaBfdSessDiscriminator

alaBfdSessNegotiatedTxInterval

alaBfdSessNegotiatedRxInterval

alaBfdSessEchoRxInterval

alaBfdSessDetectMult

alaBfdSessProtocolApps

output definitions

Local discriminator

The local discriminator.

Neighbor IP address

The IP address of the BFD neighbor.

Requested Session Type

The bit map of the session type that is requested. .

Interface IP address

The IP address of the outgoing BFD interface for this session.

Source UDP Port

The unique source UDP port used to send BFD packets for this session.

State

The state of the BFD session.

Session Operating Mode

The current operating mode of the BFD session.

Remote discriminator

The remote discriminator.

Negotiated Tx interval

The negotiated transmit interval.

Negotiated Rx interval

The negotiated receive interval.

Echo Rx interval

The Echo packet receive interval.

Detection Time Multiplier

The BFD Detection Time multiplier number.

Applications Registered

The bit map object of applications that are registered with this BFD ses-
sion.

ip bfd admin-state

Configures BFD at global level.

ip bfd interface

Configures BFD at interface level.

show ip bfd sessions statistics

Displays the statistics for all BFD sessions.

Содержание 060321-10, Rev. B



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 060321-10, Rev. B

Отзывы:

Похожие инструкции для 060321-10, Rev. B

Бренды по названию

Популярные бренды

Alcatel-Lucent 060321-10, Rev. B, Справочное руководство CLI

Результаты поиска

Содержание 060321-10, Rev. B

Отзывы:

Похожие инструкции для 060321-10, Rev. B

Бренды по названию

Популярные бренды