Alcatel-Lucent 060321-10, Rev. B Скачать руководство пользователя страница 1442

Страница: 1442 / 2354

ip pim state-refresh-ttl

PIM Commands

page 23-28

OmniSwitch CLI Reference Guide

March 2011

ip pim state-refresh-ttl

Sets the Time to Live to be used in a router’s originated State Refresh messages if the data packet’s Time
to Live is not recorded.

ip pim

state

-refresh- ttl num

Syntax Definitions

num

The Time to Live to be used. Values may range from 0 to 255.

Defaults

Platforms Supported

OmniSwitch 10K

Usage Guidelines

•

This command is supported only in the dense mode.

•

This value is used with both IPv4 and IPv6 PIM-DM.

Examples

-> ip pim state-refresh-ttl 122

Release History

Release 7.1.1; command was introduced.

Related Commands

MIB Objects

alaPimdmGlobalConfig

alaPimdmStateRefreshTimeToLive

parameter

default

num

ip pim interface

Enables or disables the PIM protocol on a specific interface.

ipv6 pim interface

Enables IPv6 PIM and configures the statistics.

show ip pim dense

Displays the status of the various global parameters for the PIM
dense mode.

show ipv6 pim dense

Displays the status of the various global parameters for the IPv6
PIM dense mode.

«
...
1440
1441
1442
1443
1444
...
»

Содержание 060321-10, Rev. B



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 060321-10, Rev. B

Отзывы:

Похожие инструкции для 060321-10, Rev. B

Бренды по названию

Популярные бренды

Alcatel-Lucent 060321-10, Rev. B, Справочное руководство CLI

Результаты поиска

Содержание 060321-10, Rev. B

Отзывы:

Похожие инструкции для 060321-10, Rev. B

Бренды по названию

Популярные бренды