Alcatel-Lucent 060321-10, Rev. B Скачать руководство пользователя страница 134 | Manualshive

Страница: 134 / 2354

background image

vlan mtu-ip

VLAN Management Commands

page 4-8

OmniSwitch CLI Reference Guide

March 2011

vlan mtu-ip

Configures the maximum transmission unit (MTU) packet size allowed for all ports associated with a
VLAN. This value is configured on a per VLAN basis, so all IP interfaces assigned to the VLAN apply the
same MTU value to packets sent on VLAN ports.

vlan vlan_id mtu-ip size

Syntax Definitions

vlan_id

An existing VLAN ID number of the VLAN to assign as the default
VLAN configured for the port.

size

Packet size value specified in bytes.

Defaults

By default, the MTU size is set to 1500 bytes (the standard Ethernet MTU size).

Platforms Supported

OmniSwitch 10K

Usage Guidelines

•

The MTU size applies to traffic sent on all switch ports that are associated with the specified VLAN
regardless of the port speed (for example, 10/100 Ethernet, gigabit Ethernet). Therefore, assign only
ports that are capable of handling the MTU size restriction to the VLAN. If the VLAN MTU size is
greater than 1500, do not assign 10/100 Ethernet ports to the VLAN.

•

By default, packets that exceed the MTU size are dropped. To enable MTU discovery and
fragmentation, use the

icmp type

command to enable the “frag needed but DF bit set” control (for

example,

icmp type 3 code 4 enable

).

•

The maximum MTU size

value for a Multi-chassis MCM-IPC VLAN its 9198.

Examples

-> vlan 200 mtu-ip 1000

-> vlan 1503 mtu-ip 9198

Release History

Release 7.1.1; command introduced.

«
...
132
133
134
135
136
...
»

Содержание 060321-10, Rev. B



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 060321-10, Rev. B

Бренд: B&K Страницы: 28

Бренд: B&K Страницы: 2

Бренд: GE Страницы: 2

Бренд: A-Neuvideo Страницы: 16

Бренд: Black Box Страницы: 9

Бренд: EtherWAN Страницы: 239

Бренд: DVIGear Страницы: 11

Бренд: Bryston Страницы: 8

Бренд: GoMax Electronics Страницы: 6

Бренд: Paralan Страницы: 45

Бренд: Cajun Страницы: 135

Бренд: StarTech.com Страницы: 2

Ultraview Pro UKT-KVM-1U08-Z

Бренд: Rose electronics Страницы: 15

Бренд: Rose electronics Страницы: 14

Бренд: Dali Страницы: 2

SmartThings STH-ETH-200

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 11

Бренд: Samsung Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды