Alcatel-Lucent 060321-10, Rev. B Скачать руководство пользователя страница 370

Страница: 370 / 2354

clear erp statistics

Ethernet Ring Protection Commands

page 8-10

OmniSwitch CLI Reference Guide

March 2011

clear erp statistics

Clears ERP statistics for all rings, a specific ring, or a specific ring port.

clear erp statistics [ring ring_id [port slot/port | linkagg agg_num]]

Syntax Definitions

ring_id

An existing ERP ring ID number. The valid range is 1- 2147483647.

slot/port

The slot number for the module and the physical port number on that
module.

agg_num

The link aggregate ID number.

Defaults

By default, statistics are cleared for all ERP rings in the switch configuration.

Platforms Supported

OmniSwitch 10K

Usage Guidelines

•

Enter a ring ID to clear the statistics for a specific ring.

•

Enter a ring ID and a ring port number or link aggregate ID to clear the statistics for a specific port or
link aggregate.

•

The specified ring ID must already exist in the switch configuration.

•

The specified port must belong to the ring identified by the ring ID.

Examples

-> clear erp statistics

-> clear erp statistics ring 5

-> clear erp statistics ring 5 port 1/2

-> clear erp statistics ring 5 linkagg 10

Release History

Release 7.1.1; command was introduced.

Содержание 060321-10, Rev. B



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 060321-10, Rev. B

Отзывы:

Похожие инструкции для 060321-10, Rev. B

Бренды по названию

Популярные бренды

Alcatel-Lucent 060321-10, Rev. B, Справочное руководство CLI

Результаты поиска

Содержание 060321-10, Rev. B

Отзывы:

Похожие инструкции для 060321-10, Rev. B

Бренды по названию

Популярные бренды